PDF Print E-mail

An Efficient & Effective Solution

The SNOWBLAST Tractor-mounted Series Snowblowers is your answer to blowing in all types of snow conditions from wet slushy snow to hard compacted frozen snow. Snowblast snowblowers will make short order of blowing snow on roads, in fields, farm yards, even inside livestock pens. Snowblast gives you effective and efficient performance combined with quality workmanship you want from your investment.


2-Year Limited Warranty (1-year parts and labor, 2-years parts).

SNOWBLAST tractor-mounted blowers use a unique spiral feeding system. Two bars stretching in front of the fans cut and slice the snow, throwing it back into the impellars. The angle of the spiral cutting bar lines up to the paddles and snow comes from the bar directly into the blade for a fast, even discharge. The fans are constructed of 3/8" backs, 3/8" paddles, and 3/8" gussets. All fans are balanced with a balance weight to prevent vibration.

Two Spout options available allow you to choose what fits your needs. Use the single chute to blow in a specific area or into trucks or use the double-chute for free casting. This allows you to tailor the blower to your specific needs. Eight bearing mounted rollers on the base of spout allow for easy rotation plus raises the spout up creating an air gap which eliminates spout freeze downs.

The outer cutting edge surrounds the entire blower for easy cutting through the toughest of packed snow. A shear Bolt on the front of each fan will shear off if the blower hits any major obstructions preventing blower damage. The shear bolts are located on the front of each fan for easy access to replace them, plus with individual fan shear bolts it eliminates any sudden stresses or jars to pass through the rest of the drive system. When a shear bolt shears, brass bushings prevent the fan from seizing onto the shaft.


On all “A” Series blowers, all chains and sprockets are completely enclosed in an oil reservoir creating quality lubrication which translates into longer chain and sprocket life and less friction. This translates into more efficiency for increased productivity. Fan shaft bearing are 4-bolt piloted flange which fit into the chain drive housing which takes the stress off of the 4 bolts. Cylindrical pressure is absorbed from the bearing, through the pilot, and into the housing itself. The blower is mounted to the tractor using a heavy duty hitch system that will accommodate a standard 3-point or Quick-Coupler hitch on the tractor.


Standard Equipment and Specifications






Cutting Width
96" (8 ft.)
108" (9 ft.)
120" (10 ft.)
144" (12 ft.)
Cutting Height
48" (4 ft.)
60" (5 ft.)
66" (5-1/2 ft.)
78" (6-1/2 ft.)
Operating Horsepower
90-180 hp
120-275 hp
200-375 hp
250-425 hp
Fan Shafts and Bearings
2-1/4" 2-7/16" 3" 3-7/16"
Drive Chain
80 80-2 80-3 80-4
Drive Chain System
Oil Bath Oil Bath Oil Bath Oil Bath
Fan Backs
3/8" 3/8" 3/8" 3/8"
Fan Paddles
3/8" 3/8" 3/8" 3/8"
Paddles per Fan
6 6 8 9
Fan Liner
1/4" 1/4" 1/4" 1/4"
Snowblower Housing
7 Ga. 7 Ga. 7 Ga. 7 Ga.
Number of Spouts
2 2 2 2
Spout Backs
7 Ga. 7 Ga. 7 Ga. 7 Ga.
Spout Sides
10 Ga. 10 Ga. 10 Ga. 10 Ga.
Skid Shoes
10” x 10” x ¾” 10” x 10” x ¾” 10” x 10” x ¾” 10” x 10” x ¾”
Cutting Edge
Bolt-On Bolt-On Bolt-On Bolt-On
Hitch (CAT)
Weight (Approx.)
3300 lbs. 4300 lbs. 6100 lbs. 9200 lbs.
Note: SNOWBLAST by Teamco reserves the right to change the above specifications at its own discretion.

Options Available

• 8600A 6" Bolt on Extension On Each Side

• 9600A 6" Bolt On Extension On Each Side
• 10800A 9" Bolt On Extension On Each Side

• 12900A 9" Bolt On Extension On Each Side

• Hydraulic Spout Flippers With Hoses

• Special Paint Colors Available (Standard Colors Are Red & Black, Green & Yellow or All Black)

Note: SNOWBLAST by Teamco reserves the right to change the above specifications at its own discretion.

Copyright © 2018 teamco. All Rights Reserved.
Joomla! is Free Software released under the GNU/GPL License.
Website by iDesign